Your speed queen washer’s drainage disaster: uncover the hidden causes
What To Know
- Disconnect the drain hose from the washer and place it in a bucket.
- If water flows out of the drain line, the blockage is likely in the washer itself.
- A noisy pump, no water flowing out of the drain hose during a drain cycle, or a washer that fails to drain completely.
A malfunctioning washing machine can be a frustrating experience, especially when it refuses to drain. If you’re grappling with this issue with your Speed Queen washer, don’t despair. This guide will delve into the potential causes and provide step-by-step troubleshooting solutions.
Common Causes of a Non-Draining Speed Queen Washer
1. Clogged Drain Hose
The drain hose is responsible for carrying wastewater out of the washer. A blockage can prevent water from draining properly. Check the hose for any kinks or obstructions.
2. Faulty Drain Pump
The drain pump is the component that forces water out of the washer. A malfunctioning pump can cause the washer to fail to drain.
3. Drain Filter Blockage
Most Speed Queen washers have a drain filter that traps lint and debris. Over time, this filter can become clogged and impede water flow.
4. Lid Switch Failure
The lid switch ensures that the washer stops operating when the lid is open. A faulty switch can prevent the washer from draining if it mistakenly detects an open lid.
5. Faulty Control Board
The control board is the brain of the washer. A malfunctioning board can affect various functions, including the draining process.
6. Clogged Drain Line
The drain line connects the washer to the drainpipe. A blockage in the drain line can prevent water from draining properly.
7. Water Inlet Valve Issues
The water inlet valve controls the flow of water into the washer. A malfunctioning valve can prevent the washer from draining properly by filling it with too much water.
Troubleshooting Steps for a Non-Draining Speed Queen Washer
1. Check the Drain Hose
Inspect the drain hose for any kinks or obstructions. Straighten out any kinks and remove any blockages.
2. Clean the Drain Filter
Locate the drain filter and remove it. Rinse the filter thoroughly with water to remove any lint or debris.
3. Reset the Lid Switch
Close the washer’s lid firmly. If the lid switch is faulty, this action may reset it.
4. Test the Drain Pump
Disconnect the drain hose from the washer and place it in a bucket. Start a drain cycle. If water flows out of the hose, the drain pump is working properly.
5. Inspect the Control Board
Visually inspect the control board for any burnt or damaged components. If you notice any issues, contact a qualified appliance repair technician.
6. Check the Drain Line
Disconnect the drain line from the washer and run a drain cycle. If water flows out of the drain line, the blockage is likely in the washer itself.
7. Diagnose Water Inlet Valve Issues
Check if the water inlet valve is allowing too much water into the washer. Disconnect the water supply and start a drain cycle. If the washer continues to drain, the water inlet valve may be faulty.
Wrapping Up: A Functional Speed Queen Washer
By following the troubleshooting steps outlined above, you can effectively address the issue of a non-draining Speed Queen washer. Remember, if you encounter any complex issues or suspect electrical problems, always consult a qualified appliance repair technician.
Frequently Asked Questions
Q: Why is my Speed Queen washer not draining after I clean the drain filter?
A: The blockage may be further down the drain hose or in the drain line. Try checking and cleaning those components.
Q: What are the signs of a faulty drain pump?
A: A noisy pump, no water flowing out of the drain hose during a drain cycle, or a washer that fails to drain completely.
Q: Can I replace the drain pump myself?
A: While it’s possible, replacing the drain pump requires some technical expertise. It’s recommended to contact a qualified appliance repair technician for this task.
