Ultimate solution: replace your maytag washer lid strike for smooth operation
What To Know
- Replacing a Maytag washer lid strike is a straightforward repair that can be completed in under an hour with the right tools and materials.
- The lid strike is a small, plastic or metal piece located on the inside of the washer, where the lid latches when closed.
- Replacing a Maytag washer lid strike is a simple and inexpensive repair that can be completed in a short amount of time.
Replacing a Maytag washer lid strike is a straightforward repair that can be completed in under an hour with the right tools and materials. This guide will provide step-by-step instructions on how to replace the lid strike on various Maytag washer models.
Tools and Materials Required
- Phillips screwdriver
- Flathead screwdriver
- New lid strike
- Rag
Identifying the Lid Strike
The lid strike is a small, plastic or metal piece located on the inside of the washer, where the lid latches when closed. It is typically attached to the washer’s top panel.
Safety Precautions
Before starting any repairs, unplug the washer from the electrical outlet and turn off the water supply.
Step-by-Step Instructions
1. Remove the Top Panel
- Locate the screws that secure the top panel to the washer’s cabinet.
- Using a Phillips screwdriver, remove the screws and lift the top panel off.
2. Disconnect the Lid Switch
- Find the wire harness that connects the lid switch to the washer’s control board.
- Unplug the wire harness from the lid switch.
3. Remove the Old Lid Strike
- Use a flathead screwdriver to pry the old lid strike loose from the washer’s top panel.
- Be careful not to damage the surrounding plastic.
4. Install the New Lid Strike
- Align the new lid strike with the holes on the top panel.
- Use a Phillips screwdriver to screw the lid strike into place.
5. Reconnect the Lid Switch
- Plug the wire harness back into the lid switch.
6. Reinstall the Top Panel
- Place the top panel back onto the washer’s cabinet.
- Secure the top panel with the screws you removed earlier.
7. Test the Lid Switch
- Plug the washer back into the electrical outlet and turn on the water supply.
- Close the washer lid and check if the washer starts.
Troubleshooting Tips
- If the washer does not start after replacing the lid strike, check the wire harness connections.
- If the washer starts but the lid does not latch properly, adjust the lid strike slightly until it aligns correctly.
- If you encounter any difficulties during the repair, refer to your washer’s user manual or consult a qualified appliance technician.
Replacing Lid Strikes on Different Maytag Models
The steps outlined above apply to most Maytag washer models. However, there may be slight variations depending on the specific model. It is recommended to refer to your washer’s user manual for model-specific instructions.
Alternative Methods for Different Washer Models
Some Maytag washer models may require alternative methods for replacing the lid strike. For example:
- Maytag Top-Load Washers with a Plastic Lid: The lid strike is usually located on the bottom of the lid. Remove the lid by lifting it up and detaching it from the hinges.
- Maytag Front-Load Washers: The lid strike is typically located on the door assembly. Remove the door assembly by unplugging the wire harness and unscrewing the hinges.
Final Thoughts
Replacing a Maytag washer lid strike is a simple and inexpensive repair that can be completed in a short amount of time. By following the steps outlined in this guide, you can restore your washer’s functionality and prevent further problems.
Frequently Asked Questions
Q: What are the signs of a faulty lid strike?
A: A faulty lid strike can cause the washer to not start or to stop mid-cycle. The lid may also not latch properly.
Q: How often should I replace the lid strike?
A: The lid strike is not a part that typically needs to be replaced regularly. However, if you experience any problems with the lid latching or the washer starting, it is worth inspecting the lid strike.
Q: Can I use a different lid strike for my Maytag washer?
A: It is not recommended to use a different lid strike for your Maytag washer. Using an incompatible lid strike can damage the washer or prevent it from operating properly.